FX1N-24MR-001 Power Specification
Rated voltage: AC100~240V
Voltage allowable range: AC85~264V
Rated frequency: 50/60Hz
Allowable instantaneous power outage time: 10ms or less
◆ Power fuse: 250V 1A
◆ inrush current: up to 30A 5ms/AC100V, up to 50A 5ms/AC200V
◆ Power consumption: 30W
◆ DC24V power supply service: 400mA
FX1N-24MR-001 Input Specification
◆ Input points:
◆ Input connection method: detachable terminal block (M3 screw)
Input form: leakage type
Input resistance: X000~X007 3.3K Ω; After X010 (all inputs of the
expansion unit) are 4.3K Ω
Input signal voltage: DC24V+10%
Input signal current: 7mA/DC24V (after X010, 5mA/DC24V)
Input ON sensitivity current: X000~X007 above 4.5mA; Above 3.5mA
after X010
Input OFF sensitivity current: below 1.5mA
Input response time:
Approximately 10ms
X000~X007 can be changed to 0-15ms through the built-in digital
filter D8020; When specified as 0, X000 and X001 are 10 μ s.
X002~X007 are 50 μ S.
Input signal form: voltage free contact input or NPN open electrode
transistor input
Circuit insulation: optocoupler insulation
◆ Input action indication: When inputting ON, the LED light is on
FX1N-24MR-001 Output Specification
◆ Output number: FX1N-24M: 10
◆ Output connection shape: terminal block (M3 screw)
Output type/format: relay output
External power supply: below AC250V and DC30V
Minimum load: DC5 V2mA
Response time: approximately 10ms
This series of PLCs cannot be equipped with expansion modules, but
a small amount of I/O can be extended by installing a BD board.
This series of PLC can achieve RS232, RS485, and RS422
communication by installing a 1N series BD board
All devices are digital input and output points.
The total number of I/O points shall not exceed 30, and the input
points shall be less than 16, and the output points shall be less
than 14FX1N-24MR-001 manual.
The MT series PLC can drive 2-way servo or stepper, commonly used
as a control system for simple robotic arms. RS-485 communication
adapter
(Requires FX3U oo BD) Memory format: EPROM.
Program Steps:
Up to 16000 steps can be used.
Battery support: No.
Method of writing and deleting: Write with ROM writer and delete
Mitsubishi PLC manual with ultraviolet light. Convert the connector
to a screw relay terminal strip.
Modules can be configured dispersedly based on the location of
connected devices. Mitsubishi frequency converter FR-E720 series.
Voltage level: 3-phase 200V.
Frequency converter capacity: 0.75KW.
In order to ensure the reliability of production, various
production machinery has a certain margin when designing and using
power drives.
When the motor cannot operate at full load, in addition to meeting
the power drive requirements,
The excess torque increases the consumption of active power,
resulting in a waste of electrical energy in the Mitsubishi PLC
manual.
The traditional speed regulation method for equipment such as fans
and pumps is to adjust the air and water supply volume by adjusting
the opening of the inlet or outlet baffles and valves
Its input power is large, and a large amount of energy is consumed
during the interception process of baffles and valves.
When using variable frequency speed regulation, if the flow
requirement is reduced, the Mitsubishi PLC manual can meet the
requirements by reducing the speed of the pump or fan. Power:
7.5kw
Purpose: High frequency braking resistor.
Can improve the utilization rate of the built-in regenerative brake
in the frequency converter
When using the FR-ABR type braking resistor, remove the short
circuit strip between the PR-PX terminals. Failure to remove the
short-circuit strip will result in the occurrence of braking
resistors
Overheating.
The setting of regenerative braking usage rate should be less than
the allowable braking usage rate in the above table FX1N-24MR-001
programming manual.
When the temperature of the braking resistor reaches 3000 ° C or
higher with the working frequency, protective measures must be
taken and heat dissipation must be carried out FX1N-24MR-001
Handbook.
MYS type resistors can be used. But please pay attention to the
allowable brake usage rate
Do not remove the short circuit strip between P/+and P1, except
when connecting the DC reactor.
Install a thermal relay to avoid overheating and burnout of the
braking resistor.
Terms:
We ships worldwide and accepts T/T and Paypal.
All items are subject to availability and passing our QA testing
and
inspection.
Turnaround Time:
Standard order processing is 1-2 business days plus shipping method
chosen.
Rush and off-hours service available for an additional fee.
Packaging and Handling:
Items are safely packaged in custom shipping cartons for
protection.
Shipping:
We ship worldwide use UPS,FedEx, DHL or Truck Freight when meeded.
Call to use a shipping service other than the ones listed.
International Customers are responsible for all Customs fees, VAT
and other
fees applied by their respective countries.
All shipments are fully insured.
Our advantage Products:
【Yaskawa】Servo Drive / Servo Motor
【Mitsubishi】Servo Drive / Servo Motor
【Honeywell】Module DCS / PLC
【Emerson】DeltaV Module / Servo Motor
【ABB】Input Output Module
【AB】Module / Touch Screen
【Rosemount】Pressure and Temperature Transmitter
【Yokogawa】Pressure Transmitter
【GE】IC69 Series PLC/ Fanuc Servo Motor and Drive
(Modicon,SMC,SICK,NORGREN,Siemens etc.)
Linture Technology Co,. Ltd
Contact person: Vivian
E-mail: linture0319@163.com
Cellphone: +0086-18026552038
Wechat:18026552038
WhatsApp:+86 18026552038
Tag:electric servo drive,ac servo drive,ac servo pack
